U0132: Lost Communication with Ride Level Control Module
Is your scanner showing U0132?
No worries. We'll show you what it means and how to deal with it.
U0132: Lost Communication with Ride Level Control Module
OVERVIEWWhat Does The U0132 Code Mean?
This code means that the Ride Level Control Module (RLCM) and other control modules on the vehicle are not talking to each other. The circuit most often used to communicate with is known as Controller Area Network bus communications, or simply put, CAN bus.
Without this CAN bus, control modules cannot exchange information, and your scan tool may not be able to get information from the vehicle, depending on which circuit is affected.
The RLCM receives input from a variety of sensors, some hardwired directly to it, some are sent over the bus communications system. These inputs allow the module to control the ride height of the vehicle utilizing inflatable air springs or air shocks, depending upon the manufacturers application.
Troubleshooting steps may vary depending upon manufacturer, type of communications system, number of wires and wire colors in the communication system.
What Are The Symptoms Of The U0132 Code?
Symptoms of a U0132 engine code may include:
- Malfunction Indicator Light On
- Incorrect vehicle ride height
- Rumbling noise heard within a minute after every initial key on
What Are The Potential Causes Of The U0132 Code?
Typically the causes for this code to set are:
- Open in the CAN bus + circuit
- Open in the CAN bus – circuit
- Short to power in either CAN bus circuit
- Short to ground in either CAN bus circuit
- Open power or ground to RLCM module – most common
- Rarely – faulty control module
How Serious Is This U0132 Code?
Severity in this case depends upon the system. Typically, once the ride height is attained, the system is shut off. As long as the failure occurs at this time, there should be no adverse effects to the vehicle/system/driving safety.
If the failure occurs due to a compressor/vent/shock/strut failure, this could be cause for concern as a safety issue may become present at any time if not already there. ALWAYS consult service information prior to disassembly/diagnosing these systems.
How Can You Fix The U0132 Code?
Check for technical service bulletins (TSB)
A good starting point is always to check for technical service bulletins (TSB) for your particular vehicle. Your issue may be a known issue with a known fix put out by the manufacturer and can save you time and money during diagnosis.
If your scan tool can access fault codes and the only one you retrieve from other modules is the U0132, try to access the RLCM module. If you can access codes from the RLCM module, then the U0132 code is either intermittent or a memory code. If unable to access codes for the RLCM module, then the U0132 code that the other modules are setting is active, and the problem is there now.
The most common failure is loss of power or ground to the RLCM module.
Check all fuses that power up the RLCM module
Check all fuses that power up the RLCM module on this vehicle. Check all grounds for the RLCM module. Locate where the ground attaching points are on the vehicle and make sure that these connections are clean and tight. If you have to, take them off, get a small wire bristle brush and baking soda/water solution and clean each one, both the connector and where it connects.
If any repairs were made, clear the diagnostic trouble codes from memory, and see if the U0132 code returns or if you are able to communicate with the RLCM module. If the code does not return or communication is re-established, then the fuses/connections were most likely your problem.
Locate the CAN C bus communication connections
If the code returns, locate the CAN C bus communication connections on your particular vehicle, most importantly the RLCM module connector. Disconnect the negative battery cable before unplugging the connector at the RLCM control module. Once located, visually inspect the connectors and wiring. Look for scraping, rubbing, bare wires, burn spots or melted plastic. Pull the connectors apart and carefully inspect the terminals (the metal parts) inside the connectors.
See if they look burned or have a green tint indicating corrosion. Use electrical contact cleaner and a plastic bristle brush if cleaning of the terminals is needed. Let dry and apply electrical grease where the terminals contact.
Before connecting the connectors back to the RLCM module, make these few voltage checks. You will need to have access to a digital volt-ohmmeter (DVOM). Verify that you have power and ground at the RLCM module. Gain access to a wiring diagram and determine where the main powers and grounds come into the RLCM module. Reconnect the battery before continuing, with the RLCM module still disconnected. Connect the red lead of your voltmeter to each B+ (battery voltage) supply coming into the RLCM module connector and the black lead of your voltmeter to a good ground (if not sure, battery negative always works). You see a reading of battery voltage. Verify that you have good grounds as well. Hook the red lead of your voltmeter to battery positive (B+) and the black lead to each ground circuit. Once again you should see battery voltage at each connection. If not, repair the power or ground circuit problem.
Check the two communication circuits
Next, check the two communication circuits. Locate the CAN C+ (or HSCAN + circuit) and CAN C- (or HSCAN – circuit). With the black lead of your voltmeter connected to a good ground, connect the red lead to CAN C+. With the Key On, Engine Off, you should see about 2.6 volts and fluctuating slightly. Next, connect the red voltmeter lead to the CAN C- circuit. You should see approximately 2.4 volts and fluctuating slightly. Other manufacturers show CAN C- at approximately .5 volts and fluctuating Key On Engine Off. Check the specifications for your manufacturer.
If all tests have passed and communication is still not possible, or you were unable to clear the U0132 fault code, the only thing left that can be done is to seek assistance from a trained automotive diagnostician, as this would indicate a failed RLCM module. Most of these RLCM modules must be programmed, or calibrated to the vehicle in order to be installed correctly.
Recommended Parts
Below are some recommended auto parts to help you address the trouble code affecting your vehicle and get it running smoothly again:
>>> WORKPRO 582-piece Crimp Terminals, Wire Connectors, Heat Shrink Tube, Electrical Repair Kit
>>> ECU
Note: During the purchasing process, please check carefully whether the part you want to buy fits your car!
Reference Sources
U0132 Lost Communication with Ride Level Control Module (RLCM), OBD-Codes.